omarchy-m-testing Install
omarchy-m-test report viCRqXJXhYZWd8wiT7cLGYQn

$ omarchy-m-test

Apple MacBook Pro (14-inch, M1 Pro, 2021)

community report

chip
M1 Pro (t6000, board j314s)
kernel
7.2.12-1-1-ARCH
stack
converged 4.0.2
build
4.0.2-2 · tester 0.1.14
system
archarm, grub, encryption on
tool
omarchy-m-test 0.1.14
catalogue
feature catalogue v14
uploaded
2026-10-29 08:58 UTC
results
48 pass · 11 fail · 14 skip
packages (10)
omarchy4.0.2-2
omarchy-settings4.0.2-2
linux-asahi7.2.12.asahi2-1
m1n11.9.9-1
uboot-asahi2026.07.asahi2-1
mesa1:26.2.5-1
vulkan-asahi1:26.2.5-1
asahi-audio4.1-1
speakersafetyd2.0.1-1
alsa-ucm-conf-asahi10-1

system

  • PASS system.identity works Device tree, asahi layer 
    model: Apple MacBook Pro (14-inch, M1 Pro, 2021)
compatible: apple,j314s apple,t6000 apple,arm-platform
chip: M1 Pro (t6000)
kernel: 7.2.12-1-1-ARCH
  • PASS system.failed-units works System services, omarchy layer 
    PASS  units            no failed system or user units
  • PASS system.snapshots works Snapshots, omarchy layer 
    PASS  snapshots        /.snapshots is a btrfs subvolume holding 0 snapshots

boot

  • FAIL boot.kernel-package doesn't work, but should on this Mac Boot chain, omarchy layer 
    FAIL  kernel           running 7.2.12-1-1-ARCH does not belong to an installed kernel package; a reboot is pending or the kernel was removed
  • FAIL boot.chain doesn't work, but should on this Mac Boot chain, omarchy layer 
    FAIL  boot-check       omarchy-apple-silicon-boot-check is not installed
  • PASS boot.files works Boot chain, omarchy layer 
    INFO  boot-file        <hex>  /boot/vmlinuz-linux-asahi
INFO  boot-file        <hex>  /boot/grub/grub.cfg
INFO  boot-file        <hex>  /boot/m1n1/boot.bin
  • PASS boot.encryption works Disk encryption, omarchy layer 
    the root filesystem is on an unlocked encrypted volume: crypt btrfs < part crypto_LUKS < disk

packages

  • PASS packages.repositories works Package repositories, omarchy layer 
    PASS  repos            omarchy-aarch64 asahi-alarm core extra alarm aur omarchy
  • PASS packages.kernel-updates works Package repositories, omarchy layer 
    PASS  kernel-repo      linux-asahi updates from [asahi-alarm]
  • PASS packages.hardware works First-boot hardware setup, omarchy layer 
    installed: mesa 1:26.2.5-1, vulkan-asahi 1:26.2.5-1, asahi-audio 4.1-1, speakersafetyd 2.0.1-1, alsa-ucm-conf-asahi 10-1

setup

  • SKIP setup.first-boot-hardware not tested First-boot hardware setup, omarchy layer 
    omarchy-provision-hardware.service never ran: this install has no deferred first-boot hardware setup
  • FAIL setup.vendor-firmware doesn't work, but should on this Mac Vendor firmware, omarchy layer 
    FAIL  vendor-firmware  omarchy-vendor-firmware.service is not installed

hardware

  • PASS hardware.drivers works A driver for every hardware node, aurora layer 
    353 hardware nodes: 303 claimed by a driver, 23 with no device of their own, 5 that no driver binds by design (CPU frequency clusters, timer, SMBIOS), 22 disabled, 0 unclaimed
  • PASS hardware.firmware works Firmware for every driver that asks, omarchy layer 
    no firmware-load failures in this boot's kernel log
  • PASS hardware.probe-errors works A driver for every hardware node, aurora layer 
    no driver probe errors in this boot's kernel log
  • PASS hardware.kernel-config works Kernel build options (compared with Asahi's), aurora layer 
    compared with Asahi's linux-asahi 7.1.13.asahi3-2 (asahi-alarm/PKGBUILDs@d585b07)
27 options differ: 14 built here but not by Asahi, 11 built by Asahi but not here, 2 set differently
CONFIG_ARM64_ERRATUM_3821522: Asahi n, this kernel y
CONFIG_ARM64_WORKAROUND_BROKEN_AMU_CONSTCNT: Asahi n, this kernel y
CONFIG_ARM64_WORKAROUND_DISABLE_CNP: Asahi n, this kernel y
CONFIG_ATALK: Asahi m, this kernel n
CONFIG_CRYPTO_DF80090A: Asahi y, this kernel n
CONFIG_CRYPTO_DRBG_CTR: Asahi y, this kernel n
CONFIG_CRYPTO_DRBG_HASH: Asahi y, this kernel n
CONFIG_CRYPTO_DRBG_HMAC: Asahi y, this kernel n
CONFIG_CRYPTO_DRBG_MENU: Asahi y, this kernel n
CONFIG_CRYPTO_FCRYPT: Asahi m, this kernel n
CONFIG_CRYPTO_PCBC: Asahi m, this kernel n
CONFIG_GENERIC_TIME_VSYSCALL: Asahi y, this kernel n
CONFIG_GPIO_SHARED_PROXY: Asahi m, this kernel y
CONFIG_HISILICON_ERRATUM_162100125: Asahi n, this kernel y
CONFIG_NETFILTER_NETLINK: Asahi m, this kernel y
CONFIG_PCIE_BUS_DEFAULT: Asahi y, this kernel n
CONFIG_PPPOX: Asahi n, this kernel m
CONFIG_RAID6_PQ_ARCH: Asahi n, this kernel y
CONFIG_RESET_APPLE_CIO: Asahi n, this kernel m
CONFIG_RPCSEC_GSS_KRB5_ENCTYPES_AES_SHA1: Asahi y, this kernel n
CONFIG_SCHED_CACHE: Asahi n, this kernel y
CONFIG_TYPEC_SN201202X: Asahi n, this kernel m
CONFIG_USB4: Asahi n, this kernel m
CONFIG_USB4_APPLE_SOC: Asahi n, this kernel m
CONFIG_USB4_CONFIGFS: Asahi n, this kernel m
CONFIG_USB4_NET: Asahi n, this kernel m
CONFIG_USB4_STREAM: Asahi n, this kernel m

gpu

  • PASS gpu.driver works GPU, asahi layer 
    asahi driver bound to 406400000.gpu
  • PASS gpu.vulkan works GPU, asahi layer 
    Asahi Vulkan driver installed (asahi_icd.json)
vulkaninfo (vulkan-tools) isn't installed, so the Vulkan version wasn't read
  • PASS gpu.opengl works GPU, asahi layer 
    renderer: Apple M1 Pro (G13S C0)
OpenGL core profile version: 4.6 (Core Profile) Mesa 26.2.5-arch1.1
OpenGL ES profile version: OpenGL ES 3.2 Mesa 26.2.5-arch1.1
installed for this run, removed at its end: mesa-utils

video

  • FAIL video.h264-on-screen doesn't work, but should on this Mac Video decoder, asahi layer 
    already installed: mpv grim ffmpeg
hardware decode asked for with --hwdec=auto-safe (mpv's configuration leaves hardware decode off)
screen: eDP-1 (built-in), H.264 test card full screen, paused
mode (from mpv's log): hardware decode vaapi (zero-copy), video output gpu-next, GPU context waylandvk
screenshot: 756x491, each bar's median colour in its middle, 64 levels allowed per channel
red bar: expected #ff0000, saw #006700 (wrong)
green bar: expected #00ff00, saw #ff95ff (wrong)
yellow bar: expected #ffff00, saw #ffa8ff (wrong)
blue bar: expected #0000ff, saw #005a00 (wrong)
magenta bar: expected #ff00ff, saw #006d00 (wrong)
cyan bar: expected #00ffff, saw #ff9bff (wrong)
on screen: 6 of 6 bars in the wrong colour (red, green, yellow, blue, magenta, cyan): green, blocky or garbled frames
  • FAIL video.hevc-on-screen doesn't work, but should on this Mac Video decoder, asahi layer 
    already installed: mpv grim ffmpeg
hardware decode asked for with --hwdec=auto-safe (mpv's configuration leaves hardware decode off)
screen: eDP-1 (built-in), HEVC test card full screen, paused
mode (from mpv's log): hardware decode vaapi (zero-copy), video output gpu-next, GPU context waylandvk
screenshot: 756x491, each bar's median colour in its middle, 64 levels allowed per channel
red bar: expected #ff0000, saw #006700 (wrong)
green bar: expected #00ff00, saw #ff95ff (wrong)
yellow bar: expected #ffff00, saw #ffa8ff (wrong)
blue bar: expected #0000ff, saw #005a00 (wrong)
magenta bar: expected #ff00ff, saw #006d00 (wrong)
cyan bar: expected #00ffff, saw #ff9bff (wrong)
on screen: 6 of 6 bars in the wrong colour (red, green, yellow, blue, magenta, cyan): green, blocky or garbled frames

display

  • PASS display.outputs works Built-in display, asahi layer 
    PASS  displays         1 active: eDP-1 3024x1964@120
  • SKIP display.external-native-mode not tested Display coprocessor (DCP), asahi layer 
    skipped: no external display connected
  • PASS display.controller works Display coprocessor (DCP), asahi layer 
    ok - the display controller card exists
  • PASS display.backlight works Display brightness, asahi layer 
    ok - the panel backlight is apple-panel-bl
  • PASS display.notch-strip works Bar clear of the notch, omarchy layer 
    ok - appledrm is showing the notch strip
  • PASS display.notch-bar works (unconfirmed) Bar clear of the notch, omarchy layer 
    asked: Look at the top bar on the built-in screen: is every icon and label clear of the camera notch?
answer: yes, by pressing Enter (the default; unconfirmed)
  • PASS display.brightness-steps works (unconfirmed) Display brightness, asahi layer 
    backlight apple-panel-bl: 250/500 at the start
stepped to 175 (read back 175), 112 (read back 112), 62 (read back 62)
put back to 250
asked: Did the built-in screen dim (or brighten) in three steps, then go back to how it was?
answer: yes, by pressing Enter (the default; unconfirmed)
  • PASS display.cursor works (unconfirmed) Built-in display, asahi layer 
    asked: Move the pointer all over the built-in screen, over the top bar too: is it visible everywhere, without trails or flicker?
answer: yes, by pressing Enter (the default; unconfirmed)

audio

  • PASS audio.sound-cards works Audio interface (MCA), asahi layer 
    PASS  sound-cards      AppleJ314, AppleJ314HPAI
  • PASS audio.default-sink works Speakers, asahi layer 
    PASS  default-sink     MacBook Pro J314 Speakers (audio_effect.j314-convolver)
  • PASS audio.speaker-dsp works Speakers, asahi layer 
    PASS speaker DSP sink present
  • PASS audio.speaker-protection works Speaker protection, omarchy layer 
    PASS  speakersafetyd   speakersafetyd is active
  • PASS audio.speaker-amps-unlocked works Speaker protection, omarchy layer 
    PASS speaker amps unlocked this boot
  • FAIL audio.microphone-mapping doesn't work, but should on this Mac Microphone mapping, omarchy layer 
    FAIL mic mapper running
  • FAIL audio.microphone-signal doesn't work, but should on this Mac Microphones, asahi layer 
    default input: effect_output.j314-mic
captured 65536 samples: peak 0, rms 0.0 (16-bit)
silence: the peak stayed under 8
  • PASS audio.speaker-tone works (unconfirmed) Speakers, asahi layer 
    speakersafetyd: active
kernel log: Speaker volumes unlocked
default output: audio_effect.j314-convolver (the speakers' DSP sink)
played a 2 s 440 Hz tone at 30% volume on audio_effect.j314-convolver
asked: Did you hear a short tone from the built-in speakers, without crackling or a pop?
answer: yes, by pressing Enter (the default; unconfirmed)
  • SKIP audio.headphone-detection not tested 3.5 mm headphone jack, asahi layer 
    asked: Plug headphones into the headphone jack now (s if you have none). Did the Mac switch its sound to them?
answer: skip
default output after: audio_effect.j314-convolver (the speakers' DSP sink)

network

  • PASS network.wifi works Wi-Fi, asahi layer 
    PASS  wifi             wlan0 is connected
  • FAIL network.wifi-backend doesn't work, but should on this Mac iwd Wi-Fi backend, omarchy layer 
    FAIL  wifi-backend     NetworkManager is not configured with wifi.backend=iwd
  • PASS network.bluetooth works Bluetooth, asahi layer 
    PASS  bluetooth        controller powered
  • PASS network.bluetooth-pairing works (unconfirmed) Bluetooth, asahi layer 
    Bluetooth controller powered (mac-check)
asked: Put a Bluetooth device (headphones, a mouse or a keyboard) in pairing mode and pair it: open Bluetooth (Super+Ctrl+B in Omarchy, or bluetui) and pick it (s if you have none to hand). Did it pair and work?
answer: yes, by pressing Enter (the default; unconfirmed)
paired devices: 3 before, 3 after
  • SKIP network.wifi-first-join not tested First join to a 5 GHz Wi-Fi network, omarchy layer 
    before: associated on 2.4 GHz (2462 MHz) with an address, on a NetworkManager connection that connects automatically
skipped: the check needs a 5 GHz network; join one and run it again

sleep

  • PASS sleep.lid-suspend works Suspend and sleep, asahi layer 
    before: eDP-1 on
lid closed: the Mac went to sleep 12.20 s later (s2idle)
woke up after 18.2 s asleep, when the lid opened
  • SKIP sleep.clamshell not tested Clamshell mode (lid closed with an external display), omarchy layer 
    skipped: no external display was connected
  • PASS sleep.wifi-after-resume works Wi-Fi, asahi layer 
    before sleeping: wlan0 connected with an IPv4 address
after waking up: an IPv4 address again 2.9 s after the Mac woke up
  • SKIP sleep.thunderbolt-after-resume not tested Thunderbolt, asahi layer 
    skipped: nothing was connected over Thunderbolt or USB4 before the Mac went to sleep

input

  • PASS input.ambient-light works Always-on processor (AOP: ambient light sensor, lid angle), aurora layer 
    ok - ALS and keyboard LED are available
  • FAIL input.auto-keyboard-light doesn't work, but should on this Mac Automatic keyboard backlight, omarchy layer 
    FAIL - the ALS keyboard loop runs
  • SKIP input.keyboard-light-follows-room not tested Automatic keyboard backlight, omarchy layer 
    before: ambient light 131 lux, keyboard light 25/255
asked: Keep it covered: did the keyboard light come on, or get brighter, within about 10 seconds?
answer: skip
while covered: ambient light 97 lux, keyboard light 25/255
  • PASS input.function-keys works (unconfirmed) Keyboard, asahi layer 
    built-in keyboard (Hyprland): apple-spi-keyboard
hid_apple fnmode: 1 (media keys first, F-keys with Fn)
asked: On the built-in keyboard, press the brightness keys (F1, F2) and the volume keys (F10, F11, F12), with Fn if they need it: did each do what its key shows?
answer: yes, by pressing Enter (the default; unconfirmed)
  • PASS input.trackpad-gestures works (unconfirmed) Trackpad, asahi layer 
    built-in trackpad (Hyprland): apple-spi-trackpad
Hyprland config: three-finger workspace swipe off
click: asked: On the built-in trackpad, press down to click: did it click?
click: answer: yes, by pressing Enter (the default; unconfirmed)
two-finger click: asked: Click with two fingers: did it right-click (a menu, where there is one)?
two-finger click: answer: yes, by pressing Enter (the default; unconfirmed)
two-finger scroll: asked: Scroll with two fingers, up and down: did it scroll smoothly both ways?
two-finger scroll: answer: yes, by pressing Enter (the default; unconfirmed)
three-finger swipe: skipped: off in your config

sep

  • SKIP sep.attach not tested Secure enclave (SEP), asahi layer 
    passive SEP attachment state unavailable or unsupported
system firmware (sepOS proxy): 26.6.2
system iBoot build: mBoot-18000.161.10
stub firmware (not running sepOS): 13.5
stub iBoot build: iBoot-8422.141.2
m1n1 stage 2: v1.9.9
actual sepOS version/build: unavailable (not exposed by the kernel)
SEP diagnostics ABI: unavailable
SEP profile: unknown
SEP boot: unknown
SEP protocol: unknown
SEP attach: unknown
SEP endpoints: unknown
SEP keystore: unknown
SEP keybag: unknown
SEP sensor: unknown
SEP touchid: unknown
SEP xart: unknown
profile and protocol describe the driver, not the running sepOS version
SEP driver bound: unavailable
/dev/sep-bio present: no
xART writes parameter: unavailable
keybag provisioning parameter: unavailable
default sensor calibration file: unavailable
sensor device-tree node: absent
sensor node enabled: unavailable
m1n1: 1.9.9-1
apple-sep.service: inactive
aurora-sep.service: inactive
fprintd.service: inactive

touch-id

  • SKIP touch-id.ready not tested Touch ID, asahi layer 
    SEP platform device unavailable
SEP diagnostics ABI: unavailable
SEP profile: unknown
SEP boot: unknown
SEP protocol: unknown
SEP attach: unknown
SEP endpoints: unknown
SEP keystore: unknown
SEP keybag: unknown
SEP sensor: unknown
SEP touchid: unknown
SEP xart: unknown
profile and protocol describe the driver, not the running sepOS version
SEP driver bound: unavailable
/dev/sep-bio present: no
xART writes parameter: unavailable
keybag provisioning parameter: unavailable
default sensor calibration file: unavailable
sensor device-tree node: absent
sensor node enabled: unavailable
m1n1: 1.9.9-1
apple-sep.service: inactive
aurora-sep.service: inactive
fprintd.service: inactive
  • SKIP touch-id.unlock not tested Touch ID, asahi layer 
    skipped: SEP biometric device unavailable

camera

  • PASS camera.isp works Camera image signal processor (ISP), aurora layer 
    camera: /dev/video1, from the ISP driver (apple-isp)
other video devices: video0 (avd)
  • PASS camera.frames works Camera image signal processor (ISP), aurora layer 
    asked ffmpeg for 30 frames from /dev/video1 (read and discarded, none kept)
stream: 1920x1080, nv12
frames: 30 of 30
  • PASS camera.image works (unconfirmed) Camera image signal processor (ISP), aurora layer 
    showed /dev/video1 live for 10 s (mpv)
asked: Did the camera window show you, live: the right way up, in focus, with natural colours and smooth movement?
answer: yes, by pressing Enter (the default; unconfirmed)

ports

  • SKIP ports.usb-c not tested USB3 on Thunderbolt ports, asahi layer 
    USB-C ports: 4 (USB-PD controller, /sys/class/typec), 1 with something plugged in
port 1: plugged in (data device, power sink)
no USB controller (no root hub in /sys/bus/usb)
USB devices: none
skipped: no USB device attached (the USB controller only comes up while something is plugged into a USB-C port); plugging one in was skipped
  • SKIP ports.thunderbolt not tested Thunderbolt, asahi layer 
    no Thunderbolt/USB4 domain registered (thunderbolt-apple-nhi)
skipped: no Thunderbolt/USB4 device attached (the Thunderbolt/USB4 host only comes up while a USB4 or Thunderbolt device is plugged in); plugging one in was skipped
  • FAIL ports.external-displays doesn't work, but should on this Mac External displays over USB-C (DP alt mode and USB4), aurora layer 
    no display connectors on the USB-C ports (no DP alt mode in this kernel)
  • SKIP ports.devices-work not tested USB3 on Thunderbolt ports, asahi layer 
    listed: 1 USB-C port(s) in use, 0 USB device(s), 0 Thunderbolt/USB4 link(s)
asked: Is everything you plugged into the USB-C ports listed above, and does it work (a stick's files open, a hub's or dock's ports work, a charger charges)?
answer: skip
  • SKIP ports.external-display-picture not tested External displays over USB-C (DP alt mode and USB4), aurora layer 
    skipped: no display in use on a USB-C port

power

  • PASS power.battery works Battery information, asahi layer 
    macsmc-battery: Full, 100% charged, charge limit 100%
  • PASS power.charge-limit works Battery information, asahi layer 
    charge limit before: 100% (charging restarts at 100%)
set 80%: the SMC reads back 80% (charging restarts at 75%)
cleared to 100%: the SMC reads back 100% (charging restarts at 100%)
put back to 100% afterwards
  • FAIL power.charge-limit-kept doesn't work, but should on this Mac Battery charge limit kept across reboots, omarchy layer 
    nothing saved in /etc/udev/macsmc-battery.conf
omarchy-battery-charge-limit isn't installed (omarchy-mac's `omarchy battery charge limit`)
nothing of omarchy-mac's restores a saved limit at boot (/usr/lib/udev/rules.d/94-omarchy-mac-battery-charge-limit.rules, /usr/lib/omarchy-mac/battery-charge-limit-restore missing)
the saved limit put back as it was (no /etc/udev/macsmc-battery.conf)
  • PASS power.idle-draw works Battery information, asahi layer 
    idle on battery for 30 s: 8.7 W average (lowest 8.4 W, highest 13.1 W), from power_now
  • PASS power.sleep-drain works Suspend and sleep, asahi layer 
    asleep for 10.7 min (s2idle), on battery
battery: 57.28 Wh to 57.64 Wh
drain: 0.0% per hour asleep, 0.00 W on average

cpu

  • PASS cpu.frequency-scaling works CPU frequency scaling, asahi layer 
    policy0: CPUs 0-1, apple-cpufreq, 600-2064 MHz, schedutil
policy2: CPUs 2-4, apple-cpufreq, 600-3036 MHz, schedutil
policy5: CPUs 5-7, apple-cpufreq, 600-3036 MHz, schedutil

benchmark

  • PASS benchmark.opengl works GPU, asahi layer score 1,444 points (glmark2 2023.01, suite 1) · compare 
    installed for this run, removed at its end: glmark2 assimp vkmark
already installed: ffmpeg
glmark2-wayland --off-screen at 1920x1080, 8 scenes of 3 s (suite 1)
renderer: Apple M1 Pro (G13S C0), OpenGL 4.6 (Compatibility Profile) Mesa 26.2.5-arch1.1
[build] use-vbo=true: 2029 fps (0.493 ms a frame)
[texture] texture-filter=linear: 2100 fps (0.476 ms a frame)
[shading] shading=phong: 1810 fps (0.553 ms a frame)
[bump] bump-render=high-poly: 1548 fps (0.646 ms a frame)
[effect2d] kernel=0,1,0;1,-4,1;0,1,0;: 1487 fps (0.673 ms a frame)
[desktop] blur-radius=5:effect=blur:passes=1:separable=true:windows=4: 701 fps (1.428 ms a frame)
[jellyfish] <default>: 1441 fps (0.694 ms a frame)
[terrain] <default>: 448 fps (2.236 ms a frame)
glmark2 score: 1444
  • PASS benchmark.vulkan works GPU, asahi layer score 3,153 points (vkmark 2025.01, suite 1) · compare 
    installed for this run, removed at its end: glmark2 assimp vkmark
already installed: ffmpeg
vkmark --winsys headless at 1920x1080, 7 scenes of 3 s (suite 1)
device: Apple M1 Pro (G13S C0)
[vertex] device-local=true: 3448 fps (0.290 ms a frame)
[texture] anisotropy=16: 3811 fps (0.262 ms a frame)
[shading] shading=phong: 2929 fps (0.341 ms a frame)
[shading] shading=cel: 2886 fps (0.347 ms a frame)
[effect2d] kernel=blur: 1684 fps (0.594 ms a frame)
[desktop] <default>: 3496 fps (0.286 ms a frame)
[cube] <default>: 3817 fps (0.262 ms a frame)
vkmark score: 3153
  • PASS benchmark.h264-decode works Video decoder, asahi layer score 402 frames/s (ffmpeg n9.0.2, suite 1) · compare 
    installed for this run, removed at its end: glmark2 assimp vkmark
already installed: ffmpeg
clip: H.264 1920x1080, 150 frames (testsrc2, libx264 veryfast), decoded 4 times to a null output (suite 1)
software decode: 600 frames in 0.42 s, 1432.0 fps
hardware decode (VA-API): 600 frames in 1.49 s, 402.1 fps
hardware decode is 0.28x software decode
ffmpeg n9.0.2
  • PASS benchmark.hevc-decode works Video decoder, asahi layer score 733 frames/s (ffmpeg n9.0.2, suite 1) · compare 
    installed for this run, removed at its end: glmark2 assimp vkmark
already installed: ffmpeg
clip: HEVC 1920x1080, 150 frames (testsrc2, libx265 ultrafast), decoded 4 times to a null output (suite 1)
software decode: 600 frames in 0.50 s, 1202.4 fps
hardware decode (VA-API): 600 frames in 0.82 s, 732.6 fps
hardware decode is 0.61x software decode
ffmpeg n9.0.2

hardware inventory

353 hardware nodes: 303 claimed by a driver, 23 with no device of their own, 5 bus or register containers with no driver of their own, 22 disabled, 0 unclaimed.

Unknown hardware

None: every node on this Mac is either claimed by a driver or known to the feature catalogue.

Kernel build options

27 options differ from Asahi's linux-asahi 7.1.13.asahi3-2 (asahi-alarm/PKGBUILDs@d585b07).

optionAsahithis kernel
CONFIG_ARM64_ERRATUM_3821522ny
CONFIG_ARM64_WORKAROUND_BROKEN_AMU_CONSTCNTny
CONFIG_ARM64_WORKAROUND_DISABLE_CNPny
CONFIG_ATALKmn
CONFIG_CRYPTO_DF80090Ayn
CONFIG_CRYPTO_DRBG_CTRyn
CONFIG_CRYPTO_DRBG_HASHyn
CONFIG_CRYPTO_DRBG_HMACyn
CONFIG_CRYPTO_DRBG_MENUyn
CONFIG_CRYPTO_FCRYPTmn
CONFIG_CRYPTO_PCBCmn
CONFIG_GENERIC_TIME_VSYSCALLyn
CONFIG_GPIO_SHARED_PROXYmy
CONFIG_HISILICON_ERRATUM_162100125ny
CONFIG_NETFILTER_NETLINKmy
CONFIG_PCIE_BUS_DEFAULTyn
CONFIG_PPPOXnm
CONFIG_RAID6_PQ_ARCHny
CONFIG_RESET_APPLE_CIOnm
CONFIG_RPCSEC_GSS_KRB5_ENCTYPES_AES_SHA1yn
CONFIG_SCHED_CACHEny
CONFIG_TYPEC_SN201202Xnm
CONFIG_USB4nm
CONFIG_USB4_APPLE_SOCnm
CONFIG_USB4_CONFIGFSnm
CONFIG_USB4_NETnm
CONFIG_USB4_STREAMnm

Asahi hardware states: Asahi Linux feature support, CC BY 3.0. More on this Mac.